Windsor SCX264 Manual do Utilizador

Read these instructions before using the machine Lea las instrucciones antes de utilizar la máquina MODELS: SCX264

HOW THE MACHINE WORKS CUTTER 24V 86039080 04/17/07 3-3 The Saber Cutter is a battery powered, self-propelled, hard floor scrubber intended for co

COMPONENTS CUTTER 24V 86039080 04/17/07 3-4 1. Control Panel 2. Front Cover 3. Recovery Tank 4. Recovery Tank Drain Hose 5. Scrub Head Shroud

CONTROLS CUTTER 24V 86039080 04/17/07 3-5 3 58 6 13 9 2121115 114 7 104 16

CONTROLS CUTTER 24V 86039080 04/17/07 3-6 1. Key Switch 2. Emergency Shut Off Switch (Optional) 3. Speed Control Knob 4. Propel Contr

CONTROLS CUTTER 24V 86039080 04/17/07 3-7 7. ACTUATOR SWITCH Adjusts the amount of brush pressure to the floor by raising or lowering the scrub

CONTROLS CUTTER 24V 86039080 04/17/07 3-8 13. BATTERY CHARGE LEVEL INDICATOR Indicates the charge level of the batteries. The meter display is

MACHINE OPERATION CUTTER 24V 86039080 04/17/07 3-9 PRE-RUN MACHINE INSPECTION Do a pre-run inspection to find possible problems that could cause

MACHINE OPERATION CUTTER 24V 86039080 04/17/07 3-10 NORMAL SCRUBBING Plan the scrubbing pattern in advance. The longest track is around the p

MACHINE OPERATION CUTTER 24V 86039080 04/17/07 3-11 DOUBLE SCRUB For floors which are heavily soiled or have thick accumulations of floor finis

MAINTENANCE CUTTER 24V 86039080 04/17/07 4-1 SERVICE SCHEDULE MAINTENANCE DAILY WEEKLY MONTHLY 100 HRS200 HRSCheck batteries after charging; add

MACHINE DATA LOG/OVERVIEW CUTTER 24V 86039080 04/17/07 2 For the name and address of your dealer contact: Wind

MAINTENANCE CUTTER 24V 86039080 04/17/07 4-2 1. Batteries 2. Squeegee 3. Aqua Mizer 4. Scrub Brushes 5. Float Shut-Off 6. Solution St

MAINTENANCE CUTTER 24V 86039080 04/17/07 4-3 1. BATTERIES The batteries provide the power to operate the machine. The batteries require regular m

MAINTENANCE CUTTER 24V 86039080 04/17/07 4-4 CHECKING BATTERY SPECIFIC GRAVITY Use a hydrometer to check the battery specific gravity.

MAINTENANCE CUTTER 24V 86039080 04/17/07 4-5 5. Replace the battery caps, and leave them in place while charging. 6. Unplug the battery connect

MAINTENANCE CUTTER 24V 86039080 04/17/07 4-6 2. SQUEEGEE BLADES The front squeegee blade allows solution to pass through channels in the blade

MAINTENANCE CUTTER 24V 86039080 04/17/07 4-7 TO ADJUST SQUEEGEE PITCH 1. Choose a smooth, level surface. Turn “ON” the key switch. Lower the

MAINTENANCE CUTTER 24V 86039080 04/17/07 4-8 4. SCRUB BRUSHES There are four different types of brushes available to cover applications from

MAINTENANCE CUTTER 24V 86039080 04/17/07 4-9 ! WARNING 6. SOLUTION STRAINER The solution strainer is located in front of the left front wheel.

MAINTENANCE CUTTER 24V 86039080 04/17/07 4-10 ! WARNING 8. TRACTION MOTOR Do not use a pressure washer to clean around the motors. Use tap pre

MAINTENANCE CUTTER 24V 86039080 04/17/07 4-11 11. VACUUM MOTOR (Refer to the Vacuum Group in the parts section of manual) Do not use a pressu

TABLE OF CONTENTS CUTTER 24V 86039080 04/17/07 3 Machine Data Log/Overview...2 Table of Contents...

MAINTENANCE CUTTER 24V 86039080 04/17/07 4-12 12. ACTUATOR SCRUB DECK REMOVAL/REPLACEMENT FOR SAFETY: Before leaving or servicing machine, st

MAINTENANCE CUTTER 24V 86039080 04/17/07 4-13 RECOMMENDED GREASING: 1-2 strokes of Mobiltemp®78 or compatible clay-based

MACHINE TROUBLESHOOTING CUTTER 24V 86039080 04/17/07 4-14 PROBLEM CAUSE SOLUTION Poor or no water pick-up Squeegee out of adjustment Adjust

MACHINE TROUBLESHOOTING CUTTER 24V 86039080 04/17/07 4-15 PROBLEM CAUSE SOLUTION Little or no solution flow to the floor Solution tank empty

HOW TO USE THIS MANUAL CUTTER 24V 86039080 04/17/07 1-1 This manual contains the following sections: - HOW TO USE THIS MANUAL - SAFETY - OPER

CUTTER 24V 86039080 04/17/07 2-1 IMPORTANT SAFETY INSTRUCTIONS When using an battery powered appliance, basic precaution must always be followed,

HAZARD INTENSITY LEVEL CUTTER 24V 86039080 04/17/07 2-2 The following symbols are used throughout this guide as indicated in their descriptions:

SAFETY LABEL LOCATION CUTTER 24V 86039080 04/17/07 2-3 NOTE: These drawings indicate the location of safety labels on the machine. If at any ti

TECHNICAL SPECIFICATIONS CUTTER 24V 86039080 04/17/07 3-1 ITEM DIMENSION/CAPACITY Nominal power 1450 W Rated Voltage 24VDC Rated Amperage 60 A

TECHNICAL SPECIFICATIONS CUTTER 24V 86039080 04/17/07 3-2 ITEM MEASURE Height 45 in. (114 cm) Length with 26 in. (66 cm) scrub head 64 in. (16